Slider

LOW VOLUME CYMBAL TRIGGER PACK – FIVE PACK

$199.99

Instantly convert any Low Volume Cymbal into an electronic crash, ride or hi-hat.

Magnatrack’s patent pending low volume cymbal triggering system delivers accuracy and feel on any reduced volume or perforated cymbal. LVCT Features an updated design that gives the trigger a more focused sensing and resists unwanted vibrations that lead to noise artifacts and double triggering.

*Additional Hi Hat Controller/Stand required.

INCLUDES

  • 5ea LVCT TRIGGERS
  • 5ea ADAPTER CABLES
  • 1ea HI-HAT NO DRILL WIRE KIT
  • 4ea FOAM HI-HAT BOTTOM KIT

THE ORIGINAL LOW VOLUME CYMBAL TRIGGER

Magnatrack’s patent pending low volume cymbal triggering system delivers accuracy and feel on any reduced volume or perforated cymbal

LVCT Features an updated design that gives the trigger a more focused sensing and resists unwanted vibrations that lead to noise artifacts and double triggering.

VERSION IMPROVEMENTS

  • Internal damping control
  • Trigger located away from strike zone
  • All velocity captured
  • Increased sensitivity
  • Increased accuracy
  • Install and remove instantly
  • Stack triggers to create multi-zones
  • Exclusive Close Proximity Focus

Our exclusive universal bolt through design works with all versions of GEN 16 and Low Volume Cymbal Brands.

INCLUDES

  • 5ea LVCT TRIGGERS
  • 5ea ADAPTER CABLES
  • 1ea HI-HAT NO DRILL WIRE KIT
  • 4ea FOAM HI-HAT BOTTOM KIT

Stacking Zones

The new LVCT is designed with Close Proximity Focus allowing for triggers to be placed near each other while maintaining independent zone isolation. By adjusting your modules sensitivity and threshold you can easily achieve natural bleed between zones and avoid unnatural sounding stops/starts.

TIPS & TRICKS

For best results don’t use a single TRS input for two triggers on the same cymbal. This will avoid trigger priority and adjacent trigger cancelation. For example, set each trigger to a single zone pre-set on its own cable.


SINGLE ZONE CRASH

DUAL ZONE CRASH

SINGLE ZONE HI HAT

TIPS & TRICKS

For Bow and Edge Zones on Ride, Crash or Hi Hat in VST and some modules:

Using a single trigger in bow location (shown above) set the bow and edge samples to same midi note as single trigger. Set the threshold of edge hits to only trigger at higher velocity than bow.

example: Bow = 1-127 velocity

Edge = 68 -127 velocity

HI HAT CONTROLLER

The most common question we get regarding Hi Hat triggering is how to control the open/close articulations. The LVCT Trigger has no effect on your modules pedal functionality. In most cases you will use the Hi Hat CC Pedal/Stand designated for your module.

Look for our Pro Control Hi Hat Stand and our Pro Control Center that mounts underneath your acoustic Hi Hat Stand Pedal Fall of 2019

RIDE OPTION ONE

2 ZONE RIDE

Follow the Tips and Tricks set-up option for the Bow and Edge Zone Single Trigger Method. Install the Bell Zone in location shown.

Set the Bell Threshold so that a natural acoustic response is triggered when in zone proximity.

RIDE OPTION TWO

3 ZONE RIDE

Follow the set-up as shown and use our MT-SM2 (stand mounted bell trigger) for zone isolation and control.

https://youtu.be/7Rmf99HsFRE
 
 

Our triggers are piezo based and are compatible with all models.
*piezo is popular inside the industry, however, some models may have trigger inputs that are both switch and piezo and may need to be configured to piezo in the module trigger setup. Some modules have the hybrid option for switch and piezo and in some cases, some module may not support piezo trigger on some inputs. (Example: ride) however, there are options for how you hook up.

No. Currently this is not an option, however, our soon to be released Lucid e-hat controller will fit all Hi-Hat stands and will allow for the natural acoustic play of the hi-hat. Installation of the controller will fit underneath the Hi-Hat stand foot pedal.

For now, you can use both the top and the bottom on a Hi-Hat stand in the closed position and use a normal control pedal for the open and close function of the module.

Our triggers and cymbals can be choked using our Low Volume Cymbal Choke MT-LVC

The Module you chose to use will have a Hi-Hat control input.  Most Modules do have a specific controller pedal that was designed for use with that module.  Many modules will allow the use of other aftermarket controllers.

*Reference your module documentation for further information.
*Additional Hi-Hat Controller/Stand required.

Please read our policy on International Shipping

Every trigger comes with our custom TRS cable for thru vent access thru the shell.

Load More

When drummer Scott O’Malley contacted us in search of an upgrade to his electronic cymbal setup the timing couldn’t have been any better. When it comes to drummers that can play any style, and cover songs as good (often better) as the original, Scott has skills few can match. With a schedule that has him playing an ungodly setlist of over 60 songs nearly every night, we knew we found the perfect guy to test the limits of our new Cymbolic Series E-Cymbals.

“Hey guys,
I just wanted to let you know I used the cymbals last night for our show. I’m very impressed by your triggers accuracy and reliability. They look amazing and I love the low profile design of the new MT-IZTII triggers. No big bulky box hanging awkwardly from the cymbals is a game changer. I’m looking forward to receiving the chokes, so as soon as you can get them to me that would be great!
I dig the natural acoustic feel of the cymbals and the way the zones have a bit of natural bleed between the triggers is something I didn’t consider possible. Great cymbals guys! Thank you again!!”
Scott O’Malley of PASSION – LAS VEGAS

Check Out PASSION’S Tour Dates
http://www.passionmusicgroup.com